Posts

coal-based-activated-carbon

Carbon (GAC) filters increasing in popularity…

Use of sediment and granular activated carbon (GAC) filters increasing in popularity.

The access to naturally fresh water is dwindling as the world’s population and global pollution increases. In addition, people’s decreasing trust in municipal water treatment and the water’s subsequent delivery infrastructure, leads to the increased use of granular activated carbon (GAC) and sediment filters that will remove organic material and sediment from the water. There are plenty of options to choose from including Purtex, Aquatrex, Matrikx, and Pentek. These filters are widely used in both standard and Big Blue sizes. Depending on your specific needs for water filtration there is an available solution for you. Innovations in the materials that are available and the technologies surrounding GAC and sediment filtration methods are making this more accessible, but what exactly is GAC and sediment filtration and how do they work?

Granular activated carbon is made from coal, wood, or coconut shells, and other high carbon organic materials. The process to activate the carbon in these organic materials involves using heat in an environment that doesn’t contain oxygen. This charring process is also why these filters are referred to as “charcoal”. When the water is passed by these GAC the activated carbon absorbs certain chemicals that are very small and dissolved. GAC filtration is able to remove organic compounds including VOCs, radon, and chlorine. The more time the water spends in contact with the GAC and the greater the surface area that is exposed, the better efficiency of organic chemical removal will be.

GAC units and sediment filters are widely used in water filters either on their own or as part of a reverse osmosis system. There are several factors that are contributing to the increasing popularity of GAC and sediment filters in water filtration including: ease of installation, ease of operation, low capital cost, and the dependability of the results. Most water filtration systems just require a plug and play replacement or installation of the GAC units. Similarly once in operation the filter only requires periodic sampling and checking for pressure drips. Usually as part of a larger water filtration system replacing the individual filters is a cost effective way to remove chemicals as well as larger particles. The life of the filters can also be extended by proper maintenance and procedures such as backwashing. GAC units are dependably able to remove most organic chemicals and sediment almost completely from the water that could negatively affect the RO membranes.

GAC and other carbon filters produced by Purtex, Aquatrex, Matrikx, and Pentek, are usually rated by the effective size of particles that they are able to remove. This is measured in microns and the most common range is from 50 microns (being the least effective) down to as small as 0.5 microns (most effective). Most household water filtration systems will contain 12 to 24 ounces of activated carbon and the most effective type of GAC is widely believed to be made from the coconut shells. As you would expect this also means that filters that contain coconut shell carbon cost about 20% more than other GAC filters.

As an effective and inexpensive way to remove volatile organic compounds and other carcinogens, GAC and sediment filtration are quickly increasing in popularity. Everyone needs clean drinking water and with increasing use of chemicals in industry and agriculture people need a dependable, effective and low cost way to treat water at point of use. GAC and sediment filters by Purtex, Aquatrex, Matrikx, and Pentek, can meet this need and give users the customized water filtration solution that they require. GAC filters can be used on their own but they are most popularly used as part of a larger water filtration system, often utilizing reverse osmosis.

ro pumps

RO Pumps and Motors…

Reverse Osmosis System Efficiency: Pumps and Motors.

The global requirement for fresh pure water is driving innovation in the water filtration industry as a whole, but especially with the reverse osmosis (RO) process. Being one of the most efficient and cost effective ways to desalinate and create clean drinking water, innovation of the components of reverse osmosis systems are helping to make the process even more efficient and cost effective. The components that are making the most impact in driving the costs down and efficiency up, aside from the reverse osmosis membrane are the RO motors and RO pumps. The reverse osmosis process is a cross-flow technology and requires higher pressure, produced by RO pumps such as Procon Pumps, to ensure the highest efficiencies.

With the recent advancements in reverse osmosis technology specifically pertaining to energy recovery devices, the reverse osmosis systems are able to utilize the pressure and the flow of the rejected water to facilitate better efficiency. This allows assembles of the RO motors and RO pumps to be smaller and decreases the overall energy requirement for the plant. Using high efficiency motors, such as Marathon motors, and high quality pumps such as Procon pumps, allows there to be less strain on the reverse osmosis membrane.

Improvements in reverse osmosis membranes have allowed the RO systems to use smaller and more efficient RO pumps and RO motors to achieve the same output. The flow rate is an important aspect of the overall efficiency of the reverse osmosis system and it can be properly regulated with quality RO pumps, like Procon pumps. There are several factors that influence the recovery of the purified water consisting of: membrane size, membrane surface area, membrane pore size, temperature, and operating pressure.

RO pumps supply the necessary pressure to overcome the resistance of the salt that gets held back by the membrane and push water through the reverse osmosis membrane. Depending on how much salt that is being filtered the RO pumps and RO motors have to be adjusted to balance enough power to overcome the salt but not so much that it strains the membrane. Typical pressures required for brackish waters are 225 – 375 psi, whereas salt water reverse osmosis (SWRO) much higher pressures in the range of 800 – 1,180 psi. Using efficient RO pumps and RO motors can ensure that the total energy expended to purify even the densest salt water uses the minimal amount of energy.

In order to get the brackish groundwater to the surface for effective treatment with a reverse osmosis system, RO pumps and RO motor have to be able to draw the groundwater from hundreds of meters under the surface. The more efficiently that the brackish water can be extracted from the ground using the latest in pump/motor technology, the less energy the reverse osmosis system will consume.

The world requires pure clean water and reverse osmosis systems seem to be leading the way. By increasing the efficiency of all of the various components such as RO pumps and RO motors, the system designers can lower cost and improve the overall purification process. The latest innovations in pump and motor technology for the reverse osmosis systems are providing improved efficiency of the total reverse osmosis system, which provides better access to clean pure water for individuals and industry.

Desalination

Desalination Growing Worldwide…

Desalination Growing Worldwide: Reverse Osmosis Membranes from Toray, Hydranautics, DOW FilmTec, GE, and Koch Leading the Way.

As the worldwide need for fresh, pure water increases an effective and cost efficient desalination process becomes more important. The process known as reverse osmosis (RO) may yield the answer that both people and companies need. This method of water purification has been around for decades, but has never been cost effective until recently. With dwindling fresh water resources, companies such as Toray, Hydranautics, FilmTec, GE, and Koch, have been developing reverse osmosis membranes that are more efficiency and cost effective. This makes saltwater reverse osmosis (SWRO) systems the leading solution to this global problem.

People need clean, pure water for consumption and industry needs pure water to facilitate processes such as mining and manufacturing. The decreased costs and increased efficiency in reverse osmosis membranes has allowed people all over the world to implement SWRO systems in order to generate the clean water that is required. Much of the innovation that has come from improving the reverse osmosis membranes has come from investment by industries, such as mining and oil refineries, throughout the middle east. Governments are also getting onboard as Australia, China, Israel, the United Arab Emirates and the United States are increasing their desalinated water production. According to the International Desalination Association, during a recent 10-year period (2001-2011) the industrial capacity for desalinated water expanded 267 percent. Using reverse osmosis membranes from Toray, Hydranautics, FilmTec, GE, and Koch, the desalinated water total capacity is now above 6.7 billion cubic meters (237 billion cubic feet) a day.

There are over 16,000 desalination plants operating worldwide today, with Saudi Arabia being the nation with the most facilities. More plants using reverse osmosis membranes are emerging online each day as the desalination industry as a whole is growing by about 15 percent a year. The increased investment which has spurred innovation by companies such as Toray with their advanced polymer technology, Hydranautics, FilmTec, GE, and Kosh, has effectively brought the price of a cubic meter of desalinated water from $3 (in the 90’s) to about 50 cents today. As the availability of fresh water becomes scarce, the innovations in desalination technologies through the use of advanced reverse osmosis membranes will afford pure clean water for everyone.

The need for pure water will only increase as the global population increases and the fresh water reserves are consumed. Innovations in desalination technology, such as reverse osmosis membranes, are quickly becoming a viable way to solve this problem. The growth of the desalination technology has been spurred by industry and people can now benefit from these advancements for processing saline water into pure drinking water. As companies such as Toray, Hydranautics, FilmTec with their high flux capacity, GE, and Koch, continue to innovate on the various RO components, including reverse osmosis membranes, the cost of a cubic meter of desalinated water will continue to decline.